|
|
| Line 1: |
Line 1: |
| ==Installation Instructions==
| | {{P5635 Installation Instructions}} |
| ''Note:'' There is no need to disassemble the 5635 camera.
| |
| ===Mounting the Camera===
| |
| #Locate the network drop above the ceiling either being a male Ethernet end (service loop) or a biscuit jack. This will have been ran back to the POE switch.
| |
| #: ''Note:'' If the switch does not have POE, a POE injector will need to be installed at the network closet.
| |
| #Remove Axis T94A02L kit from packaging. This will include the mounting bracket and the camera dome ring.
| |
| #Determine the location where the 5635 will be mounted and remove the ceiling tile
| |
| #Measuring the ceiling mount bracket, note that there is a slight lip to the camera mount
| |
| #: [[File:5635ceiingMount1.jpg|link=https://ipivs.com/wiki/images/2/29/5635ceiingMount1.jpg]]
| |
| #Find center of the ceiling tile and using a pencil, draw a circle approximately nine inches in diameter
| |
| #Using a drywall saw, cut out the section of ceiling tile where the mount will be inserted
| |
| #: [[File:5635CelingMountInstalled.jpg|link=https://ipivs.com/wiki/images/6/61/5635CelingMountInstalled.jpg]]
| |
| #Using a T20 bit, tighten the mounting arms of the ceiling mount
| |
| #: [[File:5635celingMountArm.jpg|link=https://ipivs.com/wiki/images/8/85/5635celingMountArm.jpg]] [[File:5635celingMountArmFasten.jpg|link=https://ipivs.com/wiki/images/8/83/5635celingMountArmFasten.jpg]]
| |
| #: ''Note:'' Ensure not to over tighten into the ceiling tile.
| |
| #Pass the Axis MultiCable C I/O and the Ethernet cable through the hole at the top of the camera mount
| |
| #: [[File:5635CamWire.jpg|link=https://ipivs.com/wiki/images/1/1f/5635CamWire.jpg]]
| |
| #Connect cables to their respective ports
| |
| #: [[File:5635CamWireConnect.jpg|link=https://ipivs.com/wiki/images/0/07/5635CamWireConnect.jpg]]
| |
| #Before locking the 5635 to the mounting posts in the ceiling mount, ensure that the safety cable is attached to the camera
| |
| #: [[File:5635safteyWire.jpg|link=https://ipivs.com/wiki/images/8/83/5635safteyWire.jpg]] [[File:5625safteyPost.jpg|link=https://ipivs.com/wiki/images/1/1a/5625safteyPost.jpg]]
| |
| #Insert the camera into the ceiling mount and twist until locked in place securely
| |
| #: [[File:5625CameraInstalled.jpg|link=https://ipivs.com/wiki/images/6/63/5625CameraInstalled.jpg]]
| |
| #Using a T20 bit, secure the dome ring to the camera mount
| |
| #: [[File:5635complete.jpg|link=https://ipivs.com/wiki/images/4/42/5635complete.jpg]]
| |
| #Carefully return the ceiling tile to its location
| |
| | |
| ''Note:'' If not using drop ceiling, use alternate instructions inside of the box for mounting to a hard ceiling.
| |
| ===Connecting Wiring===
| |
| #Begin but cutting two lengths of 22/2. Ensure they are long enough to reach the microphone location. One will be for audio signal. One will be for power.
| |
| #Strip the jacket off the 22/2, revealing the red, black, and common (bare wire) on both sides of the cable.
| |
| #Remove the string and plastic casings covering the red and black cables.
| |
| #Strip the red and black jackets off the wire exposing the copper. Cut copper evenly on both ends. Remove ground.
| |
| #At the Axis MultiCable C I/O, connect the ends of 22/2
| |
| #*Audio will be connected to the "In" on the audio terminal block - Red to +, Black to -
| |
| #*Power will be connected to the I/O terminal block - Red to to 2, Black to 1
| |
| #: [[File:5635MulitCableConnect.jpg|link=https://ipivs.com/wiki/images/2/2e/5635MulitCableConnect.jpg]]
| |