|
|
| (One intermediate revision by the same user not shown) |
| Line 1: |
Line 1: |
| {{Article - Manual | content =
| |
|
| |
|
| {{:VALT Privacy Button}}
| |
|
| |
| {{hr}}
| |
|
| |
| =Compatible Cameras and Wire Diagrams=
| |
| The privacy switch should be usable with any AXIS camera with at least <b>one free input</b> and <b>one free output</b>. The camera must be running firmware version 5.50 or higher.
| |
|
| |
|
| |
| {{Dashboard Row | content =
| |
| {{Dashboard Widget with Title | min-width = 250px | title = Cameras with Diagrams | background-color = #FFCB1C | content =
| |
| * [[Media:P3235_and_New_Privacy_Switch.png | Axis P3235-LVE]]
| |
| * [[Media:P3245_and_New_Privacy_Switch.png | Axis P3245]]
| |
| * [[Media:P3245_and_New_Privacy_Switch.png | Axis P3265]]
| |
| * [[Media:P3364-P3365_and_New_Privacy_Switch.png | Axis P3364/P3365*]]
| |
| * [[Media:P3374-P3375_and_New_Privacy_Switch.png | Axis P3374-V/P3375-V*]]
| |
| * [[Media:F41_and_New_Privacy_Switch.png | Axis F41 or F91]]
| |
| * [[Media:P5414-P5415_and_New_Privacy_Switch.png | Axis P5414-E/P5415-E]]
| |
| * [[Media:M5525_and_New_Privacy_Switch.png | Axis M5525 or 5526]]
| |
| * [[Media:P5635_and_New_Privacy_Switch.png | Axis P5635-E MK II]]
| |
| * [[Media:P5655_and_New_Privacy_Switch.png | Axis P5655]]
| |
| * [[Media:Q8414_and_New_Privacy_Switch.png | Axis Q8414-LVS*]]
| |
| }}
| |
|
| |
| {{Dashboard Widget with Title | min-width = 250px | title = Cameras without Diagrams | content =
| |
| * Axis P1364/65
| |
| * Axis P3301
| |
| * Axis P3304
| |
| * Axis Q3504/05 MK II
| |
| * Axis Q3518
| |
| * Axis P3935-LR
| |
| }}
| |
| }}
| |
|
| |
|
| |
| {{Aside | content = * These cameras can only be used with a single ancillary device <em>(ie: Button or privacy switch)</em>. To use these with a camera that does not have 4 I/O ports, you will need to adjust the event rules.}}
| |
|
| |
|
| |
| {{Top of Page}}
| |
| {{hr}}
| |
|
| |
| {{Float | content = {{img | file = Privacy Button On.png | width=150px}} }}
| |
| =Installation=
| |
| {{Manual lvl 2 | title = Required Parts and Tools | content =
| |
| * VALT Privacy Switch and Face Plate
| |
| * Mud Ring or Single Gang Box
| |
| * Wire Cutters/Strippers
| |
| * 22/4 solid unshielded plenum cable
| |
| * Jab Saw (used to cut hole)
| |
| * Wire fishing poles or tape
| |
| }}
| |
|
| |
| {{hr - 2}}
| |
|
| |
| {{Manual lvl 2 | title = Instructions | content =
| |
| # Determine if the button will be mounted outside the entrance of the room or at a specified location in the room.
| |
| # Using a stud finder, scan the mounting location to ensure the device is not mounted on a stud.
| |
| # Cut a hole into the drywall, large enough to fit the mud ring into it securely.
| |
| #: {{img | file = VerifactDring.JPG | width=170px}}
| |
| # Cut a hole in the wall where the privacy switch will be mounted.
| |
| # Insert the mud ring into the hole, and attach it.
| |
| # Run 22/4 from the camera to the hole.
| |
| # Strip the outer insulation from both ends of the 22/4.
| |
| #: {{img | file = Privacy1.jpg | width=375px}}
| |
| # Strip approximately 1/4 inch of insulation off of each wire in the 22/4 on the camera side
| |
| #: {{img | file = Privacy2.jpg | width=375px}}
| |
| # Insert the wires into the IO connector on the camera according to the chart below. (For a camera with a 4-pin I/O phoenix connector, use pins 3 and 4 instead of 5 and 6.)
| |
| #: {{img | file = Privacy3.jpg | width=375px}}
| |
| #: Pin 1: Green
| |
| #: Pin 2: Red
| |
| #: Pin 5: Yellow
| |
| #: Pin 6: Black
| |
| #:: ''See the chart at the end of this section for a direct mapping between the switch and I/O connector''
| |
| # Strip approximately 1/2 inch of insulation off each wire in the 22/4 on the switch side.
| |
| #: {{img | file = Privacy4.jpg | width=375px}}
| |
| # Attach the switch to the mud ring.
| |
| # Splice the wires to the switch according to the chart below.
| |
| #: {{img | file = PrivacyButton StartButton.png | width=375px}}
| |
|
| |
| * ''Connections should be made with B connectors''
| |
|
| |
| <br />
| |
| '''Wiring Map'''
| |
| <table>
| |
| <tr>
| |
| <th style="width:100px;">Privacy Switch</th>
| |
| <th>Lead Color</th>
| |
| <th>Phoenix Connector</th>
| |
| </tr>
| |
| <tr>
| |
| <td>Switch</td>
| |
| <td>Green</td>
| |
| <td>Pin 1</td>
| |
| </tr>
| |
| <tr>
| |
| <td>+</td>
| |
| <td>Red</td>
| |
| <td>Pin 2</td>
| |
| </tr>
| |
| <tr>
| |
| <td>Switch</td>
| |
| <td>Blue</td>
| |
| <td>Pin 5</td>
| |
| </tr>
| |
| <tr>
| |
| <td>-</td>
| |
| <td>Black</td>
| |
| <td>Pin 6</td>
| |
| </tr>
| |
| </table>
| |
| }}
| |
|
| |
|
| |
| {{Top of Page}}
| |
| {{hr}}
| |
|
| |
| {{:Configuring a Privacy Switch}}
| |
| }}
| |
|
| |
| [[Category:Accessories]]
| |