Public Talkback - Overhead Speaker - Revision history

IVSWikiBlue at 16:34, 5 January 2023

2023-01-05T16:34:09Z

← Older revision		Revision as of 16:34, 5 January 2023
Line 1:		Line 1:
	==Required Parts And Tools==		==Required Parts And Tools==
			<div class="section">
	* Output Speaker (may be overhead or in wall mounted)		* Output Speaker (may be overhead or in wall mounted)
	* Shure MX393 Boundary Mic		* Shure MX393 Boundary Mic
Line 16:		Line 17:
	* Wire Stripper		* Wire Stripper
	* Pencil		* Pencil
			</div>

	==Installation Instructions==		==Installation Instructions==
	===Mounting the Speaker===		===Mounting the Speaker===
			<div class="section">
	#Determine the best placement for the speaker in the room.		#Determine the best placement for the speaker in the room.
	#Carefully remove the ceiling tile		#Carefully remove the ceiling tile
Line 25:		Line 28:
	#Remove the speaker grill to be able to fasten the speaker in place. Using a drill, tighten the speaker in place. Be sure not to overtighten in order to avoid damage to the tile.		#Remove the speaker grill to be able to fasten the speaker in place. Using a drill, tighten the speaker in place. Be sure not to overtighten in order to avoid damage to the tile.
	#Replace the grill and place the tile in the ceiling.		#Replace the grill and place the tile in the ceiling.
			</div>

	===Mounting the Audio===		===Mounting the Audio===
			<div class="section">
	#Decide where the STM-1 will be located, knowing the MX393 mic will need to reach it.		#Decide where the STM-1 will be located, knowing the MX393 mic will need to reach it.
	#Using a stud finder, determine the best location to route the 22/2 cable		#Using a stud finder, determine the best location to route the 22/2 cable
Line 42:		Line 47:
	#On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.		#On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.
	#Run another length of 22/2 cable from the STM-1 to the a ST-VOX1		#Run another length of 22/2 cable from the STM-1 to the a ST-VOX1
			</div>

	===Wiring the ST-VOX1===		===Wiring the ST-VOX1===
			<div class="section">
	#Connect a line from the High Z of the STM-1 to the ST-VOX1 to the center port of the input on the device labeled as a line diagram (see wiring diagram)		#Connect a line from the High Z of the STM-1 to the ST-VOX1 to the center port of the input on the device labeled as a line diagram (see wiring diagram)
	#From the Camera, run three lines of 22/2. One will be connected to the input and two will be connected to the output.		#From the Camera, run three lines of 22/2. One will be connected to the input and two will be connected to the output.
Line 49:		Line 56:
	#The third 22/2 will connect to the speaker amp. Connect the speaker to the amp		#The third 22/2 will connect to the speaker amp. Connect the speaker to the amp
	#:'''Note:''' All lines connected to the ST-VOX1 utilize shared ground		#:'''Note:''' All lines connected to the ST-VOX1 utilize shared ground
			</div>

IVSWikiBlue: IVSWikiBlue moved page Public Talk Back - Overhead Speaker to Public Talkback - Overhead Speaker

2023-01-05T16:31:03Z

IVSWikiBlue moved page Public Talk Back - Overhead Speaker to Public Talkback - Overhead Speaker

← Older revision	Revision as of 16:31, 5 January 2023
(No difference)

IVSWikiBlue: /* Wiring the ST-VOX1 */

2021-04-14T15:12:27Z

Wiring the ST-VOX1

← Older revision		Revision as of 15:12, 14 April 2021
Line 46:		Line 46:
	#Connect a line from the High Z of the STM-1 to the ST-VOX1 to the center port of the input on the device labeled as a line diagram (see wiring diagram)		#Connect a line from the High Z of the STM-1 to the ST-VOX1 to the center port of the input on the device labeled as a line diagram (see wiring diagram)
	#From the Camera, run three lines of 22/2. One will be connected to the input and two will be connected to the output.		#From the Camera, run three lines of 22/2. One will be connected to the input and two will be connected to the output.
	#Connect the 22/2 connected to the camera input to the first port on the line diagram input. Connect one of the 22/2 connected to the camera output to the input port labeled '''Line'''. The third 22/2 will connect to the speaker.		#Connect the 22/2 connected to the camera input to the first port on the line diagram input. Connect one of the 22/2 connected to the camera output to the input port labeled '''Line'''.
			#The third 22/2 will connect to the speaker amp. Connect the speaker to the amp
	#:'''Note:''' All lines connected to the ST-VOX1 utilize shared ground		#:'''Note:''' All lines connected to the ST-VOX1 utilize shared ground

IVSWikiBlue: /* Required Parts And Tools */

2021-04-14T14:46:00Z

Required Parts And Tools

← Older revision		Revision as of 14:46, 14 April 2021
Line 11:		Line 11:
	* 22/2 audio cable		* 22/2 audio cable
	* B-connectors		* B-connectors
			* Crimper
	* Fish Tape or Glow Rods		* Fish Tape or Glow Rods
	* Electrical Tape		* Electrical Tape

IVSWikiBlue: /* Mounting the Audio */

2021-04-14T14:45:00Z

Mounting the Audio

← Older revision		Revision as of 14:45, 14 April 2021
Line 31:		Line 31:
	#: [[File:VerifactDring.JPG\|link=https://ipivs.com/wiki/images/4/4d/VerifactDring.JPG\|170px]]		#: [[File:VerifactDring.JPG\|link=https://ipivs.com/wiki/images/4/4d/VerifactDring.JPG\|170px]]
	# Using glow rods or fish tape, pass the 22/2 behind the wall routing to the STM-1		# Using glow rods or fish tape, pass the 22/2 behind the wall routing to the STM-1
			#Secure a pass through plate to the mud ring mounted for the XLR just ran
			#Place the MX393. Splice the XLR tail to 22/2 using B connectors. This mic line will connect the mic line to the STM-1
	#:'''Note:''' The wires of the XLR will wire to the +, -, and ground Input on the STM-1.		#:'''Note:''' The wires of the XLR will wire to the +, -, and ground Input on the STM-1.
	~~#Secure a pass through plate to the mud ring mounted for the XLR just ran~~
	~~#Place the MX393. This mic line will connect the mic line to the STM-1~~
	#Mount the STM-1 above the ceiling		#Mount the STM-1 above the ceiling
	#Wire the red to the + and black to the ground power terminals on the STM-1.		#Wire the red to the + and black to the ground power terminals on the STM-1.
Line 41:		Line 41:
	#On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.		#On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.
	#Run another length of 22/2 cable from the STM-1 to the a ST-VOX1		#Run another length of 22/2 cable from the STM-1 to the a ST-VOX1

	===Wiring the ST-VOX1===		===Wiring the ST-VOX1===
	#Connect a line from the High Z of the STM-1 to the ST-VOX1 to the center port of the input on the device labeled as a line diagram (see wiring diagram)		#Connect a line from the High Z of the STM-1 to the ST-VOX1 to the center port of the input on the device labeled as a line diagram (see wiring diagram)

IVSWikiBlue: /* Required Parts And Tools */

2021-04-14T14:43:38Z

Required Parts And Tools

← Older revision		Revision as of 14:43, 14 April 2021
Line 3:		Line 3:
	* Shure MX393 Boundary Mic		* Shure MX393 Boundary Mic
	* RDL STM-1 Preamp		* RDL STM-1 Preamp
	* F-XLR Tail		* XLR Tail
	* RDL ST-VOX1		* RDL ST-VOX1
	* Speaker Amplifier (Fosi or comparable)		* Speaker Amplifier (Fosi or comparable)

IVSWikiBlue: /* Required Parts And Tools */

2021-04-14T14:43:07Z

Required Parts And Tools

← Older revision		Revision as of 14:43, 14 April 2021
Line 5:		Line 5:
	* F-XLR Tail		* F-XLR Tail
	* RDL ST-VOX1		* RDL ST-VOX1
			* Speaker Amplifier (Fosi or comparable)
			* Ceiling Speaker (6 1/2")
			* Drill
			* Drywall Saw
	* 22/2 audio cable		* 22/2 audio cable
	* B-connectors		* B-connectors
	* Speaker Amplifier (Fosi or comparable)
	* Ceiling Speaker (6 1/2")
	* Fish Tape or Glow Rods		* Fish Tape or Glow Rods
	* Electrical Tape		* Electrical Tape
	* Wire Stripper		* Wire Stripper
			* Pencil

	==Installation Instructions==		==Installation Instructions==

IVSWikiBlue: /* Mounting the Speaker */

2021-04-14T14:42:04Z

Mounting the Speaker

← Older revision		Revision as of 14:42, 14 April 2021
Line 15:		Line 15:
	==Installation Instructions==		==Installation Instructions==
	===Mounting the Speaker===		===Mounting the Speaker===
			#Determine the best placement for the speaker in the room.
			#Carefully remove the ceiling tile
			#Using a pencil, trace the speaker template centered in the ceiling tile.
			#Carefully cut the tile with a drywall saw
			#Remove the speaker grill to be able to fasten the speaker in place. Using a drill, tighten the speaker in place. Be sure not to overtighten in order to avoid damage to the tile.
			#Replace the grill and place the tile in the ceiling.

	===Mounting the Audio===		===Mounting the Audio===

IVSWikiBlue: /* Required Parts And Tools */

2021-04-14T14:35:06Z

Required Parts And Tools

← Older revision		Revision as of 14:35, 14 April 2021
Line 7:		Line 7:
	* 22/2 audio cable		* 22/2 audio cable
	* B-connectors		* B-connectors
			* Speaker Amplifier (Fosi or comparable)
			* Ceiling Speaker (6 1/2")
	* Fish Tape or Glow Rods		* Fish Tape or Glow Rods
	* Electrical Tape		* Electrical Tape

IVSWikiBlue: /* Installation Instructions */

2021-04-14T14:31:28Z

Installation Instructions

← Older revision		Revision as of 14:31, 14 April 2021
Line 12:		Line 12:

	==Installation Instructions==		==Installation Instructions==
			===Mounting the Speaker===

	===Mounting the Audio===		===Mounting the Audio===
	#Decide where the STM-1 will be located, knowing the MX393 mic will need to reach it.		#Decide where the STM-1 will be located, knowing the MX393 mic will need to reach it.