Overhead Speaker Talk Back - Revision history

IVSWikiBlue: /* Mounting the Speaker */

2021-04-13T14:45:55Z

‎Mounting the Speaker

IVSWikiBlue: /* Installation Instructions */

2021-04-13T14:43:28Z

‎Installation Instructions

IVSWikiBlue: /* Required Parts And Tools */

2021-04-13T14:41:59Z

‎Required Parts And Tools

IVSWikiBlue: Created page with "==Required Parts And Tools== * Williams Talkback System IR T1 * Williams RX224 Receiver * Shure MX393 Boundary Mic * RDL STM-1 Preamp * F-XLR Tail * 22/2 audio cable * B-..."

2021-04-13T14:32:08Z

Created page with "==Required Parts And Tools== * Williams Talkback System IR T1 * Williams RX224 Receiver * Shure MX393 Boundary Mic * RDL STM-1 Preamp * F-XLR Tail * 22/2 audio cable * B-..."

New page

==Required Parts And Tools==
* Williams Talkback System IR T1
* Williams RX224 Receiver
* Shure MX393 Boundary Mic
* RDL STM-1 Preamp
* F-XLR Tail
* 22/2 audio cable
* B-connectors
* Fish Tape or Glow Rods
* Electrical Tape
* Wire Stripper

==Installation Instructions==
===Mounting the Audio===
#Decide where the STM-1 will be located, knowing the MX393 mic will need to reach it.
#Determine a suitable place to mount the RDL EZ-MCP1, ideally beneath the work station
#Using a stud finder, determine the best location to route the 22/2 cable
#Cut a hole into the drywall, large enough to fit a mud ring into it securely.
#: [[File:VerifactDring.JPG|link=https://ipivs.com/wiki/images/4/4d/VerifactDring.JPG|170px]]
# Using glow rods or fish tape, pass the 22/2 behind the wall routing to the STM-1
#:'''Note:''' The wires of the XLR will wire to the +, -, and ground Input on the STM-1.
#Secure a pass through plate to the mud ring mounted for the XLR just ran
#Using anchors and screws, mount the compressor
#Place the MX393. Plug the mic into the F-XLR tail into input of the compressor. Plug the line to the STM-1 into the output of the compressor.
#: [[File:UnderDeskMX393.jpeg|https://ipivs.com/wiki/images/5/5f/UnderDeskMX393.jpeg|500px]]
#Mount the STM-1 above the ceiling
#Wire the red to the + and black to the ground power terminals on the STM-1.
#Cut a length of 22/2 from the STM-1 to the camera. Strip the jacket on both ends. Cut away the bare wire and plastic surround the cable inside. Strip away a small piece of the red and black jackets revealing the bare copper wire.
#A short piece of 22/2 cable will also be needed (approx. 1 inch).
#Strip the jacket from the cable and remove all contents keeping only the red cable.
#On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.
#Run another length of 22/2 cable from the STM-1 to the audio connectors on the back of the speaker.

← Older revision		Revision as of 14:45, 13 April 2021
Line 31:		Line 31:
	#On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.		#On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.
	#Run another length of 22/2 cable from the STM-1 to the audio connectors on the back of the speaker.		#Run another length of 22/2 cable from the STM-1 to the audio connectors on the back of the speaker.
−	~~===Mounting the Speaker===~~

← Older revision		Revision as of 14:43, 13 April 2021
Line 31:		Line 31:
	#On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.		#On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.
	#Run another length of 22/2 cable from the STM-1 to the audio connectors on the back of the speaker.		#Run another length of 22/2 cable from the STM-1 to the audio connectors on the back of the speaker.
		+	===Mounting the Speaker===

@@ Line 1: / Line 1: @@
 ==Required Parts And Tools==
-* Williams Talkback System IR T1
+* Output Speaker (may be overhead or in wall mounted)
 * Shure MX393 Boundary Mic
 * RDL STM-1 Preamp
 * F-XLR Tail
 * 22/2 audio cable
 * B-connectors