IVSWikiBlue at 20:42, 24 March 2025

2025-03-24T20:42:22Z

← Older revision		Revision as of 20:42, 24 March 2025
Line 36:		Line 36:
	{{img \| file = Basicpolicy.PNG \| width = 800px}}		{{img \| file = Basicpolicy.PNG \| width = 800px}}
	}}		}}
			[[Category:Cameras]]

IVSWikiBlue at 16:18, 10 October 2023

2023-10-10T16:18:30Z

← Older revision		Revision as of 16:18, 10 October 2023
Line 1:		Line 1:
			{{Article \| content =
	<div class="floating_card">The following camera settings should be enabled prior to adding the camera to the VALT system.</div>		<div class="floating_card">The following camera settings should be enabled prior to adding the camera to the VALT system.</div>

	~~<div class="section">~~
	1) Browse to the camera address (you can find the camera address using the Axis IP Utility application), and set the '''root''' password.		1) Browse to the camera address (you can find the camera address using the Axis IP Utility application), and set the '''root''' password.

Line 35:		Line 35:

	{{img \| file = Basicpolicy.PNG \| width = 800px}}		{{img \| file = Basicpolicy.PNG \| width = 800px}}
	~~</div>~~		}}

IVSWikiBlue: Created page with "
The following camera settings should be enabled prior to adding the camera to the VALT system.

1) Browse to the camera..."

2023-08-03T20:13:20Z

Created page with "<div class="floating_card">The following camera settings should be enabled prior to adding the camera to the VALT system.</div> <div class="section"> 1) Browse to the camera..."

New page

<div class="floating_card">The following camera settings should be enabled prior to adding the camera to the VALT system.</div>

<div class="section">
1) Browse to the camera address (you can find the camera address using the Axis IP Utility application), and set the '''root''' password.

{{img | file = 100.jpg | width = 800px}}

2) Click on the '''Setup''' link in the upper left corner, then go to '''Basic Setup''' -> '''Video Stream''' make sure '''Compression''' is set to 30 and '''Frame Rate''' is set to 30.

{{img | file = 140.jpg | width = 800px}}

3) Click on the '''H.264''' tab and change the '''GOP Length''' to 20.

{{img | file = P5414-E_GopLength.png | width = 800px}}

4) Click on the '''Audio''' tab. Check the '''Enable Audio''' checkbox (ensure the audio format is set to '''AAC''') as shown below then press Save.

{{img | file = 141.jpg | width = 800px}}

5) Click on the '''Audio Settings''' section (using Chrome) and ensure a signal is present, using the audio indicator. When no one is speaking audio should be '''-40''' to '''-30 db''', and when someone is speaking, audio should be '''-20''' to '''-5 db'''.

{{img | file = 155.jpg | width = 800px}}

6) For proper I/O and Talkback functionality when using cameras with Axis firmware version 5.70 or greater:

Under '''Settings''' --> '''System Options''' --> '''Security''' --> '''Users''' you will need to set '''Allow Password''' type to '''Unencrypted Only''', as shown below.

After this change, you will need to restart the camera.

{{img | file = 5514.jpg | width = 800px}}

7) For proper I/O and Talkback functionality when using cameras with Axis firmware version 8.0 or greater:

Under '''Settings''' --> '''Plain Config''' --> '''Network''' --> you will need to set '''Authentication policy''' to '''Basic''', as shown below.

{{img | file = Basicpolicy.PNG | width = 800px}}
</div>

Camera Settings Older Firmware - Revision history

IVSWikiBlue at 20:42, 24 March 2025

IVSWikiBlue at 16:18, 10 October 2023

IVSWikiBlue: Created page with "The following camera settings should be enabled prior to adding the camera to the VALT system. 1) Browse to the camera..."

IVSWikiBlue: Created page with "
The following camera settings should be enabled prior to adding the camera to the VALT system.

1) Browse to the camera..."